213 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 213. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
213 dimensions and recorded technical data
The recorded 213 base designation measures 65×120×23 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 13 recorded variants are listed. A dash means the value is missing, not zero.
Catalogue parameters for 213
Choose the complete brand and marking before reading a value. These source-labelled records add dimensions, construction and engineering properties where they were recorded; a shared model number does not establish interchangeability.
Units, ranges and minimum/maximum qualifiers are retained. The data is a dated catalogue reference, not a certified drawing, a complete current specification or an operating approval.
SKF 213 — 35 recorded parameters
Deep groove ball bearing with filling slots
Reference: SKF product catalogue; source snapshot 2026-09-02.
Read the complete suffix and recorded construction. Similar dimensions do not prove identical seals, clearance, precision or material.
Values shown are retained from the recorded source. Zero boundary dimensions and zero load ratings from incomplete legacy feeds are withheld rather than presented as usable specifications.
Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | Not separately recorded | 65.0 mm |
| Outside diameter | Not separately recorded | 120.0 mm |
| Width | Not separately recorded | 23.0 mm |
Performance
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | Not separately recorded | 60.5 kN |
| Basic static load rating | Not separately recorded | 58.5 kN |
| Reference speed | Not separately recorded | 10000.0 r/min |
| Limiting speed | Not separately recorded | 6000.0 r/min |
Properties
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Filling slots | Not separately recorded | With |
| Number of rows | Not separately recorded | 1 |
| Locating feature, bearing outer ring | Not separately recorded | Without |
| Bore type | Not separately recorded | Cylindrical |
| Cage | Not separately recorded | Sheet metal |
| Matched arrangement | Not separately recorded | No |
| Radial internal clearance | Not separately recorded | CN |
| Material, bearing | Not separately recorded | Bearing steel |
| Coating | Not separately recorded | Without |
| Sealing | Not separately recorded | Without |
| Relubrication feature | Not separately recorded | Without |
| Indicative carbon footprint for new product | Not separately recorded | 4.0 kg CO 2 e |
Logistics
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Product net weight | Not separately recorded | 1.08 kg |
Engineering — Dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Bore diameter | d | 65 mm |
| Outside diameter | D | 120 mm |
| Width | B | 23 mm |
| Shoulder diameter | d 1 | ≈ 83.3 mm |
| Recess diameter | D 2 | ≈ 105.8 mm |
| Chamfer dimension | r 1,2 | min. 1.5 mm |
Engineering — Abutment dimensions
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Diameter of shaft abutment | d a | min. 74 mm |
| Diameter of housing abutment | D a | max. 111 mm |
| Radius of shaft or housing fillet | r a | max. 1.5 mm |
Engineering — Calculation data
| Parameter | Source symbol | Recorded value |
|---|---|---|
| Basic dynamic load rating | C | 60.5 kN |
| Basic static load rating | C 0 | 58.5 kN |
| Fatigue load limit | P u | 2.5 kN |
| Reference speed | Not separately recorded | 10000 r/min |
| Limiting speed | Not separately recorded | 6000 r/min |
| Minimum load factor | k r | 0.04 |
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF213Deep groove ball bearing with filling slots |
| 60.5 kN | 58.5 kN | 10000 rpm | 6000 rpm | 1.08 kg1080 g |
| SKF213-2ZDeep groove ball bearing with filling slots and integral sealing |
| 60.5 kN | 58.5 kN | 10000 rpm | 4800 rpm | 1.1 kg1100 g |
| SKF213/C3Deep groove ball bearing with filling slots |
| 60.5 kN | 58.5 kN | 10000 rpm | 6000 rpm | 1.08 kg1080 g |
| SKF213 NRDeep groove ball bearing with filling slots and snap ring |
| 60.5 kN | 58.5 kN | 10000 rpm | 6000 rpm | 1.1 kg1100 g |
| SKF213-ZDeep groove ball bearing with filling slots and integral sealing |
| 60.5 kN | 58.5 kN | 10000 rpm | 6000 rpm | 1.1 kg1100 g |
| SKF213-ZNRDeep groove ball bearing with filling slots and integral sealing |
| 60.5 kN | 58.5 kN | 10000 rpm | 6000 rpm | 1.1 kg1100 g |
| TIMKEN213KDDDeep groove ball bearing |
| 57.2 kN | 40 kN | — | — | 1.02 kg1020 g |
| TIMKEN213KDFS50000Deep groove ball bearing |
| 57.2 kN | 40 kN | — | — | 1.02 kg1020 g |
| TIMKEN213KFS50000Deep groove ball bearing |
| 57.2 kN | 40 kN | — | — | 1.02 kg1020 g |
| TIMKEN213NPPDeep groove ball bearing |
| 57.2 kN | 40 kN | — | — | 1.02 kg1020 g |
| TIMKEN213WDeep groove ball bearing |
| 81.6 kN | 65.1 kN | — | — | 1.21 kg1210 g |
| TIMKEN213WDDNDeep groove ball bearing |
| 81.6 kN | 65.1 kN | — | — | 1.21 kg1210 g |
| TIMKEN213WDNDeep groove ball bearing |
| 81.6 kN | 65.1 kN | — | — | 1.21 kg1210 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 213 | Without | Not recorded | CN | Sheet metal | Bearing steel | None |
| SKF 213-2Z | Shield on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 213/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 213 NR | Without | Not recorded | CN | Sheet metal | Bearing steel | None |
| SKF 213-Z | Shield on one side | Not recorded | CN | Sheet metal | Bearing steel | None |
| SKF 213-ZNR | Shield on one side | Not recorded | CN | Sheet metal | Bearing steel | None |
| TIMKEN 213KDD | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 213KDFS50000 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 213KFS50000 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 213NPP | Sealed | Not recorded | Not recorded | Nylon cage | Not recorded | Not recorded |
| TIMKEN 213W | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 213WDDN | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 213WDN | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
213
Deep groove ball bearing with filling slots
View full technical record →NSK21304CDE4
Spherical roller bearing
View full technical record →NSK21304CDKE4
Spherical roller bearing
View full technical record →FAG21304-E1-XL-TVPB
Spherical Roller Bearing
View full technical record →FAG21304-E1-XL-TVPB-C3
Spherical Roller Bearing
View full technical record →SKF21305 CC
Spherical roller bearing
View full technical record →SKF21305 CC/C3
Spherical roller bearing
View full technical record →NSK21305CDE4
Spherical roller bearing
View full technical record →NSK21305CDKE4
Spherical roller bearing
View full technical record →FAG21305-E1-XL-TVPB
Spherical Roller Bearing
View full technical record →FAG21305-E1-XL-TVPB-C3
Spherical Roller Bearing
View full technical record →TIMKEN21305EJW33
Spherical roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.