211 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 211. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
211 dimensions and recorded technical data
The recorded 211 base designation measures 55×100×21 mm (inside diameter d × outside diameter D × width B). This answer uses unsuffixed records from SKF. It does not assign the same dimensions or operating ratings to every suffix.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 19 recorded variants are listed. A dash means the value is missing, not zero.
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| SKF211Deep groove ball bearing with filling slots |
| 48.4 kN | 44 kN | 12000 rpm | 7000 rpm | 0.656 kg656 g |
| SKF211-2ZDeep groove ball bearing with filling slots and integral sealing |
| 48.4 kN | 44 kN | 12000 rpm | 5600 rpm | 0.679 kg679 g |
| SKF211-2ZNRDeep groove ball bearing with filling slots and integral sealing |
| 48.4 kN | 44 kN | 12000 rpm | 5600 rpm | 0.701 kg701 g |
| SKF211/C3Deep groove ball bearing with filling slots |
| 48.4 kN | 44 kN | 12000 rpm | 7000 rpm | 0.657 kg657 g |
| SKF211 NRDeep groove ball bearing with filling slots and snap ring |
| 48.4 kN | 44 kN | 12000 rpm | 7000 rpm | 0.676 kg676 g |
| SKF211-ZDeep groove ball bearing with filling slots and integral sealing |
| 48.4 kN | 44 kN | 12000 rpm | 7000 rpm | 0.666 kg666 g |
| SKF211-ZNRDeep groove ball bearing with filling slots and integral sealing |
| 48.4 kN | 44 kN | 12000 rpm | 7000 rpm | 0.69 kg690 g |
| INA211-XL-KRRDeep groove ball bearing |
| 46 kN | 29 kN | — | — | 0.85 kg850 g |
| TIMKEN211KDDFS50000Deep groove ball bearing |
| 43.4 kN | 29.2 kN | — | — | 0.64 kg640 g |
| TIMKEN211KDDGFS50000Deep groove ball bearing |
| 43.4 kN | 29.2 kN | — | — | 0.64 kg640 g |
| TIMKEN211KDFS50000Deep groove ball bearing |
| 43.4 kN | 29.2 kN | — | — | 0.64 kg640 g |
| TIMKEN211KFS50000Deep groove ball bearing |
| 43.4 kN | 29.2 kN | — | — | 0.64 kg640 g |
| TIMKEN211KGFS50000Deep groove ball bearing |
| 43.4 kN | 29.2 kN | — | — | 0.64 kg640 g |
| TIMKEN211NPDeep groove ball bearing |
| 43.4 kN | 29.2 kN | — | — | 0.58 kg580 g |
| TIMKEN211PPFS50000Deep groove ball bearing |
| 43.4 kN | 29.2 kN | — | — | 0.64 kg640 g |
| TIMKEN211RR2Deep groove ball bearing |
| 43.4 kN | 29.2 kN | — | — | 0.71 kg710 g |
| TIMKEN211WDeep groove ball bearing |
| 54.3 kN | 40.9 kN | — | — | 0.68 kg680 g |
| TIMKEN211WDDDeep groove ball bearing |
| 54.3 kN | 40.9 kN | — | — | 0.68 kg680 g |
| TIMKEN211WDNDeep groove ball bearing |
| 54.3 kN | 40.9 kN | — | — | 0.68 kg680 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| SKF 211 | Without | Not recorded | CN | Sheet metal | Bearing steel | None |
| SKF 211-2Z | Shield on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 211-2ZNR | Shield on both sides | Not recorded | CN | Sheet metal | Bearing steel | Grease |
| SKF 211/C3 | Without | Not recorded | C3 | Sheet metal | Bearing steel | None |
| SKF 211 NR | Without | Not recorded | CN | Sheet metal | Bearing steel | None |
| SKF 211-Z | Shield on one side | Not recorded | CN | Sheet metal | Bearing steel | None |
| SKF 211-ZNR | Shield on one side | Not recorded | CN | Sheet metal | Bearing steel | None |
| INA 211-XL-KRR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| TIMKEN 211KDDFS50000 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 211KDDGFS50000 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 211KDFS50000 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 211KFS50000 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 211KGFS50000 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 211NP | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 211PPFS50000 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 211RR2 | Sealed | Not recorded | Not recorded | Nylon cage | Not recorded | Not recorded |
| TIMKEN 211W | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 211WDD | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 211WDN | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
211
Deep groove ball bearing with filling slots
View full technical record →SKF211-2Z
Deep groove ball bearing with filling slots and integral sealing
View full technical record →SKF211-2ZNR
Deep groove ball bearing with filling slots and integral sealing
View full technical record →SKF211/C3
Deep groove ball bearing with filling slots
View full technical record →TIMKEN211KDDFS50000
Deep groove ball bearing
View full technical record →TIMKEN211KDDGFS50000
Deep groove ball bearing
View full technical record →TIMKEN211KDFS50000
Deep groove ball bearing
View full technical record →TIMKEN211KFS50000
Deep groove ball bearing
View full technical record →TIMKEN211KGFS50000
Deep groove ball bearing
View full technical record →TIMKEN211NP
Deep groove ball bearing
View full technical record →SKF211 NR
Deep groove ball bearing with filling slots and snap ring
View full technical record →TIMKEN211PPFS50000
Deep groove ball bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.