202 bearing dimensions & suffix variants
Look up recorded dimensions for designations beginning with 202. The table retains complete manufacturer designations so special suffixes and different dimensional variants remain visible.
On this page5 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
202 dimensions and recorded technical data
Use the named dimensions for each complete record below. A generic d×D×B answer is not asserted where the base record is missing, dimension symbols are unverified, or the product uses a different geometry such as a housing or thrust assembly. Suffix records are not substituted for a missing base specification.
The numeric series boundary is preserved: a longer number is not included merely because its first digits match. 9 recorded variants are listed. A dash means the value is missing, not zero.
No recorded variant matches these filters. Clear a filter to see other records; no substitute has been inferred.
| Brand / full designation | Named dimensions (mm / in) | Dynamic C (kN) | Static C0 (kN) | Reference speed (rpm) | Limiting speed (rpm) | Mass (kg / g) |
|---|---|---|---|---|---|---|
| INA202-XL-KRRDeep groove ball bearing |
| 8.1 kN | 3.7 kN | — | — | 0.05 kg50 g |
| TIMKEN202KGFS50000Deep groove ball bearing |
| 8.47 kN | 4.09 kN | — | — | 0.04 kg40 g |
| TIMKEN202KLDDeep groove ball bearing |
| 8.47 kN | 4.09 kN | — | — | 0.05 kg50 g |
| TIMKEN202KLD3Deep groove ball bearing |
| 8.47 kN | 4.09 kN | — | — | 0.05 kg50 g |
| TIMKEN202KRR3Deep groove ball bearing |
| 6.8 kN | 3.34 kN | — | — | 0.05 kg50 g |
| TIMKEN202KTTDeep groove ball bearing |
| 8.47 kN | 4.09 kN | — | — | 0.05 kg50 g |
| TIMKEN202NPP2Deep groove ball bearing |
| 7.62 kN | 3.7 kN | — | — | 0.04 kg40 g |
| TIMKEN202NPP5Deep groove ball bearing |
| 7.62 kN | 3.7 kN | — | — | 0.04 kg40 g |
| TIMKEN202PPGFS50000Deep groove ball bearing |
| 7.62 kN | 3.7 kN | — | — | 0.04 kg40 g |
Compare recorded seals, clearance, precision and materials
Manufacturer wording is retained. A missing property is not inferred from another brand or a similar suffix.
| Brand / designation | Closure | Original precision | Clearance | Cage | Material | Lubricant |
|---|---|---|---|---|---|---|
| INA 202-XL-KRR | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded | Not recorded |
| TIMKEN 202KGFS50000 | Open | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 202KLD | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 202KLD3 | Shielded | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 202KRR3 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 202KTT | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 202NPP2 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 202NPP5 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
| TIMKEN 202PPGFS50000 | Sealed | Not recorded | Not recorded | Steel cage | Not recorded | Not recorded |
How to compare these values
- Use the displayed dimension names and original symbols. Housing length L, height H2 and flange width are not bearing outside diameter D. A catalogue width with an unverified symbol must not be assumed to be inner-ring width B or assembly width T. Open the product record for mounting dimensions and geometry.
- Inch values are calculated from the recorded millimetres using 25.4 mm per inch, rounded to six decimal places. They do not change a metric bearing into an inch-series bearing. Gram values are converted from the recorded mass in kilograms.
- C and C0 describe different rating conditions. They are not a single safe working-load limit and cannot replace an application load calculation.
- Reference and limiting speeds are separate catalogue values. The source grease/oil context is shown where recorded. Lubricant, seals, loads, fit, clearance and cooling affect the usable operating speed.
- A common base number does not prove equivalent seals, clearance, precision, material or interchangeability. Open the full designation for these fields.
Related prefix matches — other model numbers may appear
These discovery results can contain a longer number or a different component. They are not specifications for the requested exact model. Open the complete product to inspect its original geometry.
20204-TVP
Barrel roller bearing
View full technical record →FAG20205-K-TVP-C3
Barrel roller bearing
View full technical record →FAG20205-TVP
Barrel roller bearing
View full technical record →FAG20205-TVP-C3
Barrel roller bearing
View full technical record →FAG20206-K-TVP-C3
Barrel roller bearing
View full technical record →FAG20206-TVP
Barrel roller bearing
View full technical record →FAG20206-TVP-C3
Barrel roller bearing
View full technical record →FAG20207-K-TVP-C3
Barrel roller bearing
View full technical record →FAG20207-TVP
Barrel roller bearing
View full technical record →FAG20207-TVP-C3
Barrel roller bearing
View full technical record →FAG20208-K-TVP-C3
Barrel roller bearing
View full technical record →FAG20208-TVP
Barrel roller bearing
View full technical record →Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.