35×62×14 mm bearing size chart
Compare catalogue records with a 35 mm bore, 62 mm outside diameter and 14 mm recorded width. Identical boundary dimensions do not establish interchangeability.
On this page8 sections ⌄
Find by measured dimensions
Enter bore d, outside diameter D and width B. Use decimals or inch fractions such as 1/2 or 1 1/4.
35×62×14 mm: what this result means
The dimensional answer is 35×62×14 mm: inside diameter d × outside diameter D × recorded axial width. Every candidate below has these three nominal catalogue values and a retained manufacturer source. Narrow by the original construction, brand and reported technical properties. For tapered, thrust, needle and matched designs, inspect which component or assembly the width describes; this table is a dimensional shortlist, not a replacement approval.
A bore is not the diameter of a loose precision ball. Complete bearings, inserts and other catalogue components can have different functions even where the recorded dimensions match. Keep the original product type visible when making a shortlist.
| Requested dimension | Millimetres | Inches | Selection meaning |
|---|---|---|---|
| Inside diameter d | 35 mm | 1.377953 in | Nominal catalogue value, not a shaft/housing fit tolerance |
| Outside diameter D | 62 mm | 2.440945 in | Nominal catalogue value, not a shaft/housing fit tolerance |
| Recorded width B / T | 14 mm | 0.551181 in | Nominal catalogue value, not a shaft/housing fit tolerance |
Inch conversions use 25.4 mm per inch and are displayed to six decimals. A converted metric dimension does not make a bearing an inch-series design.
Are your measurements in millimetres or inches?
The chart on this page uses millimetres. An unlabelled search such as 35 × 62 × 14 does not tell us which unit was measured. Choose the unit for those same numbers before opening a different catalogue lookup.
Inside diameter d: 35 mm; Outside diameter D: 62 mm; Recorded axial width: 14 mm
Search 35 × 62 × 14 mmConversion and reinterpretation are different
Same physical size, another unit: divide a dimension in millimetres by 25.4 to express it in inches. The bearing does not change.
The original numbers were inches: multiply those numbers by 25.4 to obtain the millimetre values used in the catalogue. For the numbers on this page, that means 889 × 1574.8 × 355.6 mm, not 35 × 62 × 14 mm.
One inch is exactly 25.4 millimetres. Displayed values are rounded to six decimals; rounding is not a manufacturing tolerance. Confirm the measured axes and the complete bearing construction before comparing models.
The unit choice updates the lookup immediately. The main chart below remains the millimetre size in this page heading. A catalogue search can have no recorded match; that means no match in the available data, not that the size cannot exist. A loose precision ball has one diameter and is not a complete bearing d×D×width measurement.
Filter every recorded match for 35×62×14 mm
Keep the known dimensions fixed while narrowing all 215 complete-dimension records in this snapshot. Read the full designation and original construction before opening a product record.
Ball-bearing searches: select Ball bearings to remove roller bearings and mounting components. The requested bore belongs to a complete bearing; this is not a loose precision-ball diameter chart.
Showing the first 24 of 215 records. Filters update immediately.
| Brand / full designation | Original product type | Recorded d×D×width (mm) | Closure | Clearance | Precision |
|---|---|---|---|---|---|
| KOYO6007 | Deep groove ball bearing | 35×62×14 | Open | Not reported | Not reported |
| SKF6007 | Deep groove ball bearing | 35×62×14 | Without | CN | P6 and tighter width tolerance |
| TIMKEN6007 | Deep groove ball bearing | 35×62×14 | Open | Not reported | Not reported |
| KOYO6007 2RD | Deep groove ball bearing | 35×62×14 | Extremely light contact sealed | Not reported | Not reported |
| KOYO6007 2RS | Deep groove ball bearing | 35×62×14 | Contact sealed | Not reported | Not reported |
| SKF6007 2RSJEM | Deep groove ball bearing | 35×62×14 | Seal on both sides | C3 | Not reported |
| SKF6007 2RSNRJEM | Deep groove ball bearing | 35×62×14 | Seal on both sides | C3 | Not reported |
| KOYO6007 2RU | Deep groove ball bearing | 35×62×14 | Non-contact sealed | Not reported | Not reported |
| SKF6007 2ZJEM | Deep groove ball bearing | 35×62×14 | Shield on both sides | C3 | Not reported |
| SKF6007 2ZNRJEM | Deep groove ball bearing | 35×62×14 | Shield on both sides | C3 | Not reported |
| SKF6007 JEM | Deep groove ball bearing | 35×62×14 | Without | C3 | Not reported |
| SKF6007 N | Deep groove ball bearing with snap ring groove | 35×62×14 | Without | CN | P6 and tighter width tolerance |
| SKF6007 RSJEM | Deep groove ball bearing | 35×62×14 | Seal on one side | C3 | Not reported |
| SKF6007 TN9/HC5C3 | Hybrid ceramic deep groove ball bearing | 35×62×14 | Without | C3 | Not reported |
| SKF6007 ZJEM | Deep groove ball bearing | 35×62×14 | Shield on one side | C3 | Not reported |
| KOYO6007 ZZ | Deep groove ball bearing | 35×62×14 | Shielded ZZ | Not reported | Not reported |
| TIMKEN6007-2RS | Deep groove ball bearing | 35×62×14 | Sealed | Not reported | Not reported |
| TIMKEN6007-2RS-C3 | Deep groove ball bearing | 35×62×14 | Sealed | Not reported | Not reported |
| TIMKEN6007-2RS-C3/VSL609 | Deep groove ball bearing | 35×62×14 | Sealed | Not reported | Not reported |
| TIMKEN6007-2RS-NR | Deep groove ball bearing | 35×62×14 | Sealed | Not reported | Not reported |
| TIMKEN6007-2RS-NR-C3 | Deep groove ball bearing | 35×62×14 | Sealed | Not reported | Not reported |
| TIMKEN6007-2RS/VSL609 | Deep groove ball bearing | 35×62×14 | Sealed | Not reported | Not reported |
| SKF6007-2RS1 | Deep groove ball bearing with seals or shields | 35×62×14 | Seal on both sides | CN | P6 and tighter width tolerance |
| SKF6007-2RS1/C3 | Deep groove ball bearing with seals or shields | 35×62×14 | Seal on both sides | C3 | Not reported |
Open current catalogue for these dimensions →
Snapshot 2026-10-02. Counts describe the available records, not every bearing made. The original product type is retained. Matched sets, units, flanges, sleeves and tapered assemblies require their own drawing; a recorded width is not automatically a single radial-ring width B. Unreported properties remain unknown. Matching dimensions do not approve substitution.
Keep these dimensions and choose a brand
Choosing a brand opens the existing live filters immediately with the dimensional conditions retained. These are catalogue candidates, not interchange approvals.
How to narrow the shortlist
- Confirm which dimension was measured: bore d, outside D or axial width. Do not use a flange diameter as the bearing outside diameter.
- Measure the remaining boundary dimensions and preserve the original marking. A single known diameter usually identifies several different models.
- Select the required construction, seals, clearance and precision in the live results. An unreported field is still unknown.
- Check the exact product drawing, load ratings, speed and mounting requirements before considering a replacement.
Check the drawing before substituting
Nominal dimensions are not shaft-fit tolerances. Different variants can add grooves, flanges, wider rings or assembly components. When the table has different dimensions, the complete designation—not the shared prefix—controls.
Reference basis & data limits
Manufacturer terminology is retained in the product records. Technical reference basis: JTEKT Basic Bearing Knowledge (boundary dimensions, tolerance classes and lubrication); NSK Bearing ABCs (lubrication, designations and clearance); NTN technical FAQs (closure codes and component interchange); SKF rolling-bearing selection and maintenance references.
Selection workflows and catalogue grouping are BearingScope editorial aids. Verify the current drawing and application requirements before using a candidate. Missing database information is not converted into an assumed match.