99,016 bearing records · search, filter and compare

info@bearingscope.com
Independent technical reference

Tesla wheel bearing & hub reference: Model 3, Model Y and Model S

Compare source-scoped hub fastener requirements by model, manual edition and left-hand wheel position. Separate hub mounting bolts from halfshaft nuts, inspect replacement rules, and check the Model Y wheel-type restriction before assuming that a similar hub is interchangeable.

Compare profilesWheel restrictionsNext checkSources & limits
On this page4 sections
Select the scope, then read the data

Which hub procedure are you checking?

Separate the hub-to-knuckle bolts from the halfshaft nut. Choose a model, manual edition and location; matching a manual profile is not a VIN or part-number fitment approval.

9scoped profiles
3 model families

9 profiles shown. Manual years describe the document scope, not a fitment guarantee.

Wheel-type restrictions ↓

At-a-glance comparison

Model / manual editionProcedureHub boltsHalfshaft / axle nut
Model 32017–2023Front LHDual Motor85 NmReuse300 NmReplace
Model 32017–2023Front LHRWD85 NmReuseNot includedRWD front procedure
Model 32017–2023Rear LHNot separated in heading85 NmNot established300 NmReplace
Model Y2020–2024Front LHDual Motor85 NmReuse300 NmReplace
Model Y2020–2024Front LHRWD85 NmReuseNot includedRWD front procedure
Model Y2020–2024Rear LHNot separated in heading85 NmReuse300 NmReplace
Model Y2025+Rear LHNot separated in heading85 NmReuse300 NmReplace
Model S2012–2020Front LHNot separated in heading90 NmCheck patch-bolt rule245 NmReplace · Dual Motor only
Model S2021+Front LHNot separated in heading90 NmReuse245 NmReplace
2017–2023 manual

Model 3 · Front LH

Dual Motor

Hub-to-knuckle bolts

Reuse

85 Nm62.7 lb-ft

Within the selected manual procedure.

Source-listed tool
18 mm socket
Source scope →

Front halfshaft nut

Replace

300 Nm221.2 lb-ft

Within the selected manual procedure.

Source-listed tool
32 mm deep impact socket
Source scope →
Important limits for this profile
  • The hub mounting bolts and the driven halfshaft nut are separate fasteners with different values and replacement rules.
  • The procedure names a hydraulic hub puller and a magnetic-field viewing card. A generic bearing press is not automatically a substitute.
  • A front/rear wording inconsistency in the source's lubrication step is not resolved by inference here; verify that step in the applicable manual.

Source procedure: 2017-2023 Model 3 Service Manual — Hub - Front - LH (Dual Motor) (Remove and Replace).

2017–2023 manual

Model 3 · Front LH

RWD

Hub-to-knuckle bolts

Reuse

85 Nm62.7 lb-ft

Within the selected manual procedure.

Source-listed tool
18 mm socket
Source scope →
Important limits for this profile
  • This is the RWD front-hub procedure. A halfshaft-nut value from the Dual Motor procedure is not added to this profile.
  • The manual asks for a tone-ring inspection before installation. A matching mounting envelope does not establish the encoder specification.

Source procedure: 2017-2023 Model 3 Service Manual — Hub - Front - LH (RWD) (Remove and Replace).

2017–2023 manual

Model 3 · Rear LH

Not separated in heading

Hub-to-knuckle bolts (3)

Not established

85 Nm62.7 lb-ft

The inline procedure supplies torque, but does not explicitly label these bolts Reuse or Replace.

Source-listed tool
Not established in this extract
Source scope →

Rear halfshaft nut

Replace

300 Nm221.2 lb-ft

The procedure requires a new nut and washer.

Source-listed tool
32 mm deep impact socket
Source scope →
Important limits for this profile
  • The rear procedure includes electronic parking-brake service-mode requirements. This reference is not the full brake or lifting procedure.
  • Keep lubricant off the halfshaft splines. The manual's limited mating-face lubricant instruction is not a general instruction to grease the hub or splines.
  • A seized hub needs a different removal plan if proceeding would damage the halfshaft boot. Do not force a removal based only on the torque table.

Source procedure: 2017-2023 Model 3 Service Manual — Hub - Rear - LH (Remove and Replace).

2020–2024 manual

Model Y · Front LH

Dual Motor

Hub-to-knuckle bolts

Reuse

85 Nm62.7 lb-ft

Within the selected manual procedure.

Source-listed tool
18 mm socket
Source scope →

Front halfshaft nut

Replace

300 Nm221.2 lb-ft

Within the selected manual procedure.

Source-listed tool
32 mm deep impact socket
Source scope →
Important limits for this profile
  • The hub mounting bolts and the driven halfshaft nut are separate fasteners with different values and replacement rules.
  • The procedure names a hydraulic hub puller and a magnetic-field viewing card. A generic bearing press is not automatically a substitute.
  • A front/rear wording inconsistency in the source's lubrication step is not resolved by inference here; verify that step in the applicable manual.

Source procedure: 2020-2024 Model Y Service Manual — Hub - Front - LH (Dual Motor) (Remove and Replace).

2020–2024 manual

Model Y · Front LH

RWD

Hub-to-knuckle bolts

Reuse

85 Nm62.7 lb-ft

Within the selected manual procedure.

Source-listed tool
18 mm socket
Source scope →
Important limits for this profile
  • This is the RWD front-hub procedure. A halfshaft-nut value from the Dual Motor procedure is not added to this profile.
  • The manual asks for a tone-ring inspection before installation. A matching mounting envelope does not establish the encoder specification.

Source procedure: 2020-2024 Model Y Service Manual — Hub - Front - LH (RWD) (Remove and Replace).

2020–2024 manual

Model Y · Rear LH

Not separated in heading

Hub-to-knuckle bolts

Reuse

85 Nm62.7 lb-ft

Within the selected manual procedure.

Source-listed tool
18 mm socket
Source scope →

Rear halfshaft nut

Replace

300 Nm221.2 lb-ft

Within the selected manual procedure.

Source-listed tool
32 mm deep impact socket
Source scope →
Important limits for this profile
  • The rear procedure includes electronic parking-brake service-mode requirements. This reference is not the full brake or lifting procedure.
  • Keep lubricant off the halfshaft splines. The manual's limited mating-face lubricant instruction is not a general instruction to grease the hub or splines.
  • A seized hub needs a different removal plan if proceeding would damage the halfshaft boot. Do not force a removal based only on the torque table.

Source procedure: 2020-2024 Model Y Service Manual — Hub - Rear - LH (Remove and Replace).

2025+ manual

Model Y · Rear LH

Not separated in heading

Hub-to-knuckle bolts

Reuse

85 Nm62.7 lb-ft

Within the selected manual procedure.

Source-listed tool
18 mm socket
Source scope →

Rear halfshaft nut

Replace

300 Nm221.2 lb-ft

Within the selected manual procedure.

Source-listed tool
32 mm deep impact socket
Source scope →
Important limits for this profile
  • For this manual's 18-inch steel-wheel condition, read the part-family restriction below before selecting a hub.
  • A June 2026 revision changed the hub-bolt value to 85 Nm. This snapshot uses the current table, not the older 115 Nm value.
  • A magnetic pickup tool or parts tray can damage the bearing tone-ring pattern. The manual calls for a non-magnetic resting surface.
  • The rear procedure includes electronic parking-brake service-mode requirements. This reference is not the full brake or lifting procedure.

Source procedure: Model Y 2025+ Service Manual — Hub - Rear - LH (Remove and Replace).

2012–2020 manual

Model S · Front LH

Not separated in heading

Hub-to-knuckle bolts (4)

Check patch-bolt rule

90 NmNm only in this source

The procedure requires replacement of patch bolts; this extract does not identify every bolt as reusable.

Source-listed tool
Not established in this extract
Source scope →

Front axle nut — Dual Motor only

Replace

245 NmNm only in this source

Dual Motor vehicles only; replace the axle nut and wedge-lock washer.

Source-listed tool
Not established in this extract
Source scope →
Important limits for this profile
  • Air-suspension vehicles require the manual's Jack-mode setup before lifting. A manual edition is not a VIN-level applicability check.
  • The April 2026 revision says the rotor-retaining bolt does not need to be reinstalled; hub 1420121-00-A does not have its mounting hole. Do not turn the removal value into a universal installation requirement.
  • Preserve the tone-ring magnetic pattern and check the applicable post-work brake and alignment requirements.

Source procedure: 2012-2020 Model S Service Manual — Hub - Front - LH (Remove and Replace).

2021+ manual

Model S · Front LH

Not separated in heading

Hub-to-knuckle bolts (4)

Reuse

90 Nm66.4 lb-ft

Within the selected manual procedure.

Source-listed tool
18 mm deep socket
Source scope →

Front halfshaft nut

Replace

245 Nm180.7 lb-ft

Within the selected manual procedure.

Source-listed tool
32 mm deep impact socket
Source scope →
Important limits for this profile
  • This later Model S manual explicitly labels the hub bolts Reuse and the halfshaft nut Replace. Do not backfill those labels into the earlier Model S procedure.
  • The magnetic-field viewing card is used to inspect the tone ring. A bearing dimension alone cannot verify the encoder or vehicle fitment.
  • The procedure also covers brake-caliper fasteners and alignment checks; those separate requirements are not replaced by this hub-fastener reference.

Source procedure: 2021+ Model S Service Manual — Hub - Front - LH (Remove and Replace).

A size match can still be wrong

Model Y 2025+ rear hub: wheel-type restriction

The reviewed rear-LH procedure gives the following part-family condition for steel versus alloy wheels. Its caution specifically addresses 18-inch steel wheels. The asterisk is a family prefix, not a complete orderable part number or a universal fitment approval.

Source part-family prefixSteel wheelAlloy wheel
1044121*Permitted by this tablePermitted by this table
1044122*Permitted by this tablePermitted by this table
1044123*Not permitted by this tablePermitted by this table
1044124*Not permitted by this tablePermitted by this table

This table does not identify your vehicle's complete replacement number. Verify the VIN, wheel specification, current part revision and full procedure before choosing a hub.

Read the source scope ↓

What are you trying to establish?

A noise sourceA torque value cannot diagnose a hum. Record speed, load, tyre and brake observations before attributing a noise to a bearing.Wheel-bearing noise investigation →The correct hub or bearingKeep wheel position, complete part number, encoder and assembly identity together. Do not approve an interchange from dimensions alone.Hub identification checks →A replacement candidateA service fastener table is not a cross-reference list. Check the whole assembly specification and any vehicle restrictions.Replacement evidence checklist →

Source editions, gaps and verification

Independently organized by BearingScope from Tesla's public service manuals, checked 2026-10-04. Source addresses, snapshots and row-level checks are retained in the private audit. Original published unit pairs are preserved; missing imperial values are not calculated and presented as source facts.

Still not established here: VIN-specific fitment, every model generation, RH procedures, Model S rear procedures, aftermarket interchange, bearing dimensions, diagnosis of an individual vehicle, or a complete safe repair sequence. “Not separated in heading” describes the source heading; it does not mean every drive configuration is approved.

View the 12 source scopes
  • 2017-2023 Model 3 Service Manual — Hub - Front - LH (RWD) (Remove and Replace)Checked 2026-10-04. Applies only to the named manual and procedure.
  • 2017-2023 Model 3 Service Manual — Torque Specifications - SuspensionChecked 2026-10-04. Applies only to the named manual and procedure.
  • 2017-2023 Model 3 Service Manual — Hub - Rear - LH (Remove and Replace)Checked 2026-10-04. Applies only to the named manual and procedure.
  • 2020-2024 Model Y Service Manual — Hub - Rear - LH (Remove and Replace)Checked 2026-10-04. Applies only to the named manual and procedure.
  • 2020-2024 Model Y Service Manual — Torque Specifications - SuspensionChecked 2026-10-04. Applies only to the named manual and procedure.
  • Model Y 2025+ Service Manual — Hub - Rear - LH (Remove and Replace)Checked 2026-10-04. Applies only to the named manual and procedure.
  • Model Y 2025+ Service Manual — Model Y 2025+ Service ManualChecked 2026-10-04. Applies only to the named manual and procedure.
  • 2017-2023 Model 3 Service Manual — Hub - Front - LH (Dual Motor) (Remove and Replace)Checked 2026-10-04. Applies only to the named manual and procedure.
  • 2020-2024 Model Y Service Manual — Hub - Front - LH (Dual Motor) (Remove and Replace)Checked 2026-10-04. Applies only to the named manual and procedure.
  • 2020-2024 Model Y Service Manual — Hub - Front - LH (RWD) (Remove and Replace)Checked 2026-10-04. Applies only to the named manual and procedure.
  • 2012-2020 Model S Service Manual — Hub - Front - LH (Remove and Replace)Checked 2026-10-04. Applies only to the named manual and procedure.
  • 2021+ Model S Service Manual — Hub - Front - LH (Remove and Replace)Checked 2026-10-04. Applies only to the named manual and procedure.
Search the consolidated catalogue

Find, filter and compare bearing model data in one place.

Open model search